ATD Customs Contender Bull Bar Fitting Instructions | Ford Ranger Super Duty

Step-by-step fitting instructions for the ATD Customs Contender Bull Bar and side rails for the 2025+ Ford Ranger Super Duty. Fit it yourself, or take it to a nearby 4x4 accessories fitter or local trusted mechanic. Fitting instructions and downloadable checklist: https://www.atdcustoms.com.au/fit/fsd This video shows the complete installation process for the ATD Customs Contender Bull Bar and optional side rails. Use this video together with the official ATD Customs Contender Bull Bar and Side Rails Fitting Checklist. Read through the complete checklist and watch the fitting video before starting installation, then follow the video and checklist together as you work through the fit. The numbered chapters in this video correspond directly with the numbered steps in the fitting checklist, making it easy to jump straight to the step you’re working on. The installation covers vehicle preparation, chassis bracing, wiring, transfer and installation of factory parking sensors, camera and radar, optional winch and spotlight installation, bull bar fitment, electrical and safety-system checks, and optional side rail installation. IMPORTANT: Installation may require specialised tools and techniques and should be carried out by a competent person. Follow all installation notes, warnings and torque values in the current fitting checklist. Keep the vehicle ignition OFF while factory sensors, radar, camera or associated safety-technology components are disconnected or being relocated. CHAPTERS 00:00 Step 1 – Check parking sensors & front camera 00:17 Step 2 – Remove negative battery terminal 00:33 Step 3 – Remove number plate 00:41 Step 4 – Remove radiator top cover 01:05 Step 5 – Remove plastic bumper centre 01:43 Step 6 – Remove front grille 02:14 Step 7 – Unplug main bumper harness, camera & washer line 03:23 Step 8 – Remove main bumper 03:46 Step 9 – Remove genuine bash plate 04:07 Step 10 – Remove/trim intercooler shroud 04:59 Step 11 – Remove recovery side bolts 05:17 Step 12 – Remove captive nut holders 05:37 Step 13 – Remove bumper captive nut brackets 06:01 Step 14 – Install ATD chassis bracing 10:03 Step 15 – Reinstall intercooler shroud 10:28 Step 16 – Install Deutsch plugs 13:02 Step 17 – Remove battery holder 13:14 Step 18 – Install ATD engine-bay wiring loom 18:46 Step 19 – Install ATD indicator wiring loom 21:33 Step 20 – Transfer centre parking sensor harness 23:17 Step 21 – Transfer safety-tech harness 29:03 Step 22 – Install ATD intercooler vents 29:55 Step 23 – Install front camera 30:31 Step 24 – Install RUNVA 11XP winch (optional) 35:58 Step 25 – Install centre parking sensor harness 36:33 Step 26 – Route safety-tech harness 37:38 Step 27 – Connect sensor harnesses 38:16 Step 28 – Install radar 39:24 Step 29 – Install spotlights (optional) 39:37 Step 30 – Install ATD bull bar harness 41:55 Step 31 – Secure wiring 43:56 Step 32 – Lift bull bar into position 44:50 Step 33 – Loosely install bull bar mounting bolts 45:30 Step 34 – Reconnect wiring above radiator 47:14 Step 35 – Connect winch power & earth (optional) 50:42 Step 36 – Reinstall battery holder 51:15 Step 37 – Reconnect negative battery terminal 51:28 Step 38 – Test electrical systems & accessories 53:25 Step 39 – Reinstall front grille 54:16 Step 40 – Reinstall radiator top cover 54:46 Step 41 – Reinstall genuine bash plate 55:21 Step 42 – Install ATD bash plate 56:09 Step 43 – Check radar alignment 57:13 Step 44 – Reinstall number plate 57:41 Step 45 – Check parking sensors 58:21 Step 46 – Remove genuine side steps 58:49 Step 47 – Install front side-rail mounts 1:01:01 Step 48 – Install rear side-rail mounts 1:03:46 Step 49 – Attach side rail to bull bar 1:05:20 Step 50 – Fit, align & tighten side rail to mounts 1:10:17 Step 51 – Sit down, drink your beer & admire your ATD bull bar 1:10:27 Step 52 – Repeat Step 51 until satisfied ATD Customs Australian-made frontal protection and accessories, built with Attention To Detail. https://www.atdcustoms.com.au/fit/fsd https://www.atdcustoms.com.au/product... #atdcustoms #fordrangersuperduty #contenderbullbar