Installation: Curt Custom Fifth Wheel Installation Kit for Chevy/GMC on a 2006 Chevrolet Silverado

Click for more info and reviews of this CURT 5th Wheel Hitch Rails: https://www.etrailer.com/5th-Wheel-Hi... Check out some similar 5th Wheel Hitch Rails options: https://www.etrailer.com/5th-wheel.htm Search for other popular Chevrolet Silverado parts and accessories: https://www.etrailer.com/vehicle/2006... https://www.etrailer.com Don’t forget to subscribe!    / etrailertv   Full transcript: https://www.etrailer.com/tv-install-c... Hi there, Chevy owners. Today, on your 2006 Chevrolet 2500, we're gonna be taking a look at and showing you how to install Curt's above bed rail kit. And this is what our rail kit looks like when it's installed. It is an above the bed rail kit, so it will take up a little bit of your bed space. But it is fairly low, so it doesn't really inhibit it too much, maybe just when you're sliding stuff back and forth. It is gonna allow you to attach a fifth wheel to your vehicle. There is multiple slots in it, so it is designed to work with many different fifth wheels out there. We've got a ton of fifth wheels here at etrailer. Our customer here is using Curt's Q20, but we do have a lot available here. This kit is custom-fit for this vehicle which makes the installation easier than a universal rail kit would be. The brackets for the sides are custom-fit for it. So, that way, all of the holes in the brackets line up with the holes in the frame, making the installation significantly easier. Your rails sit here on top. You simply mark them out and we drill out the holes and they will bolt directly to our side plates as well as our bed to give us a nice, secure mounting point for our fifth wheel here. You'll attach your fifth wheel using pins. You can see, there's multiple different holes here, depending on the size of the fifth wheel that you're gonna be putting in here, and the pins attach here. Just for the pin and clip, there's a total of four of those at each corner of our fifth wheel. Now, as far as the installation goes on this, the instruction says, it'll take about 90 minutes to install. I think they're a little bit low on the low end there just because these outer bolts can be pretty tricky to get to to torque down because the frame is so close to them. And the side plates have to torque to it, very massively high torque, so you are gonna have to have a very large torque wrench to be able to do this as well. So, just keep that in mind. If you don't have these pieces of equipment at home, you need a torque wrench that can go above 300-foot pounds, if you don't have that, you may wanna seek professional installation 'cause the tools to do this job can be quite expensive as well. Again, we talked about 90 minutes is what the instruction says, but I found that this is really closer to probably about a three or four-hour install, just because of how hard it is to get to some of those bolts to tighten them down. And if you're doing this at home and you don't have a lift, you guys probably know why you'd also wanna take that into account. If you've got to lift, you could probably should have a couple hours off that. But with no lift, it is quite a bit more difficult than it would be, than like it is here, where we have a lift at the shop. So, now that we've covered some of the features here of our fifth wheel, why don't you follow along with us in the shop and we'll show you how to get it installed. We'll begin our installation by lowering down our spare tire. We'll get that thing out of the way. It'll make our installation a whole lot easier if that's not there. So, now we'll need to position our front rail. Your front and rear rail are gonna be the same, so you just pick one of your two rails and set it into position. We'll need to center it side to side. And we'll also need to set it the correct distance from the back of our truck bed for the appropriate size that our truck bed is. So, whether you got a shorter or a long bed, the measurement is gonna change, so you wanna refer to your instructions for the right one. And we'll be using a short bed here, and we're gonna measure it from here at the end of the bed. We'll find the measurements outlined in our instructions, and we're gonna make a little mark there. We're gonna do the same thing on the other side, that way, we'll have a mark on each side to make sure our rail's in the correct position. Next, I'm just gonna be marking the center, so I'm just going line to line here and I'm gonna find that center line. I'm just gonna mark that right on there, so we know where the center is. We'll now mark our holes and prepare to drill them. And we're gonna be using a combination of a paint stick and a center punch. For our front rail here, the one closest to the cab, we're gonna mark at the center of the outer holes on each side and the center hole towards the cab. So, we're just gonna