VERY SCARY Turbine Jet MAIDEN • HSDJETS T-45 K70G4+ RC PLANE • (English/Français 4K 60fps HDR)

Watch ALL the video to know all the clues ! 🇺🇸 Hi folks 👋🏻🤠 Thank you for watching this video and don't forget to subscribe so you don't miss anything (it's free but it helps content creators a lot) 🙏🏻🥰 If you want to help me to expand my squadron 😜 or buy a specific plane to review, you can help me by making a small donation via my PayPal link https://www.paypal.me/arthurjanin?loc... Thank you very much in advance my friends 🤩🙏🏻 🇫🇷 Salut les copains 👋🏻🤠 Merci d’avoir regardé cette vidéo et n’oubliez pas de vous abonner pour ne rien manquer (c’est gratuit et pourtant ça aide énormément les créateurs de contenus) 🙏🏻🥰 Si vous voulez m’aider à agrandir mon escadron 😜 ou que j’achète un avion en particulier, vous pouvez m’aider en faisant un petit don via mon lien PayPal https://www.paypal.me/arthurjanin?loc... Merci beaucoup beaucoup d’avance les amis 🤩🙏🏻 📸 Follow me on Instagram :   / arthuraerorc   ⏰ TikTok : https://vm.tiktok.com/ZMNYCqUhC/ You can buy my things here ⬇️ 💨 Kingtech Turbines ➡️ https://www.kingtechturbine.lu 🇺🇸 ⚓️ HSDJETS T-45 Turbine Ready ➡️ https://hsdjetsuk.com/product/t-45-go... 🎮 Jeti Rx and DS16 ➡️ https://www.opale-paramodels.com/fr/ ‪@OpaleParamodels‬ 🔋CNHL LiPo ➡️ https://chinahobbyline.com/?ref=I5Ew9... ✈️ Jets and more ➡️ https://www.turbines-rc.com/fr/?aff=4 🇺🇸 ⚓️ HSDJETS T-45 Goshawk Turbine Foam Jet (PNP + Smoke, no turbine) Wingspan 1502mm, length 1903mm, dry weight 7.7kg, flying weight 10,5kg (1800ml kero + 120ml UAT + 750ml smoke) Turbine : Kingtech 70G4+ ➡️ https://kingtechturbine.lu/KingTech-K... Very hard foam (20 times EPO) Control system included MFC-2085 2 LiPo CNHL 2S 2200mah XT60 (required) With slats and air brakes ❌ Book CG 150mm from slat root leading edge, straight along fuselage and aligned with first wing screw! 📏 Rates after the 2nd flight (For the elevator, measure from the leading edge of the tail, centered with fuselage marks) : low / mid / high Elevator : 20/20/20mm (you have to change servo arm linkage to outermost hole ⚠️) Ailerons : 15/18/23mm Rudder : 25/30/40mm Flaps : 20 / 35mm (5mm up elevator) MFC-2085 inputs: R11 : slats R13 : smoke pump R14 : airbrakes ⏰ Flights with timers and voltage 1st (filmed) : 4m40 turbine and 50% fuel left (pump factor was 600 but totally wrong so I set at 400 after maiden) 2nd (filmed) : 3m18 turbine and 70% fuel left (I finally set pump factor at 350) 0:00 Présentation française 0:28 English presentation 1:00 MFC/GSU start 1:55 K70 Start-up 🔥 3:01 Take-Off 3:28 Trimming / increase elevator throws 4:47 Half throttle to full throttle climb out 5:07 Roll 5:25 Close flyby 5:37 Full flaps 5:48 Go around 6:13 Airbrakes deployed / Landing (full up elevator) 6:45 First thoughts 7:28 Telemetry check 8:13 Please Subscribe 🙏🏻😍 8:39 Elevator servo arm 😳 9:12 Details photos #turbine #rcplane #kingtech #jet #jeti #opale #radiocontrol #setup #modellbau #t45 #eflite #new #hsdjets #perfect #foam #crash #fms #freewing